Please select a wishlist

Roto Elite Latch Deadbolt 2 Hooks Double Spindle Multipoint Door Lock

Roto Elite Latch Deadbolt 2 Hooks Double Spindle Multipoint Door Lock
Log in to view prices and stock availability

This Elite Standard multipoint door lock features 2 Hooks, 1 Deadbolt & 1 Latch.

Elite multipoint door locks cover a wide range of different applications. They are made in Europe and feature a "Silbear" coating which offers 480 hours salt spray protection.

Identifying an Elite lock starts with the faceplate, which should be stamped with an Elite logo. This gearbox features a slot and a small hole below the slot appearing above the top spindle which is a piercing for bolt through handles.

If these locks look familiar, that’s because they are. Elite took over the manufacturing of these locks from Roto-Frank when they discontinued the range. They use the same tooling, with the exception of the new Silbear coating, they are made to the same specification as the original locks. You may recognise them from our catalogues as the MVD range or "Roto mark 2" locks. Gearboxes cannot be changed with the original locks but they do offer a relatively simple complete lock swap.

Many Elite locks are available in standard and compact versions designed for shorter doors. They feature the same 950mm handle height but a shorter overall length of 1810mm.

Elite gearboxes are available as a 35mm single spindle lock or with a 35mm or 45mm double spindle. Gearboxes measure 200mm high x backset + 19mm. Be sure to account for 2mm for the faceplate when measuring the backset.

Gearbox deadbolts project 20mm and are 32mm high. The latch is 30mm high and projects 10mm. The distance between the bottom of the latch and the top of the deadbolt is 63mm.

Centres are positioned at 62mm and 92mm with the top spindle being 122mm from the bottom of the case. Single spindle locks have a round hole where the second spindle would usually be located. The gearbox is pierced to accept a bolt through fixing 19mm from the top spindle, and the slot above for fixings is 42mm above the spindle.

Elite hooks can throw in either opposite directions, or upwards, depending on the model. They feature the same Silbear coating as the rest of the lock, which offers up to 480 hours salt spray testing.

Operation: Double Spindle

To lock the door

1. On closing the door, the latch is automatically engaged.

2. Lift the handle up to engage the locking points.

3. Lock the system by turning the key.

To unlock the door

1. Unlock the system by turning the key.

2. Push the handle downwards to disengage the locking points.

3. A further quarter turn of the key will retract the latch.

  • 480 hours salt spray tested to EN1675 Grade 5

We stock a range of associated products for Elite Standard multipoint door locks, including keeps, spindles, handles and accessories.

You may find this lock used as a timber door lock or a composite door lock.

How can I tell who the manufacturer is of my multipoint lock?

Check down the faceplate and look for a brand name or logo to identify the manufacturer.


How do I find out the operation of my multipoint door lock?

  • 1. If you only use the key to unlock all of the locking points then the operation is called Key Wind.
  • 2. If you lift the handle and turn the key to lock then the operation is called Lift Lever.
  • 3. If from the outside you unlock with the key, pull handle down to disengage the locking points and turn the key to open the door then this operation is called Nightlatch or Split Spindle.
  • 4. If lifting the handle fully locks the door without the use of a key then this operation is called Auto Locking.


How do I measure my multipoint door lock?

Always measure in millimetres.

  • 1. Backset – Measure the distance from the edge of the faceplate back to where the key goes into the door cylinder.
  • 2. Centres – Measure the distance from centre of handle spindle down to where the key goes into the door cylinder.
  • 3. Locking points – Measure the distance from centre of the locking point to the centre of handle spindle then repeat for other locking points.
  • 4. Faceplate – Measure the distance across the width of the face and full length of the faceplate.
  • 5. Gearbox – Measure the height and depth of the gearbox.


How do I know if my multipoint door lock is left or right handed?

99% of multipoint door locks are field reversible, instructions for which are under product information. For those models which are handed please refer to the handing chart to determine which hand you require.


Do you stock a gearbox only for this lock?

Yes our part number is ELITECASE35.

All product options

All product options
Product Code Backset Spindle Faceplate Operation StockRRPDiscountPriceQuantity
ELITE352HR20
35mm
Double 8mm
Flat 20mm - Round Ends
Double Spindle
---
--,--
--
ELITE452HR20
45mm
Double 8mm
Flat 20mm - Round Ends
Double Spindle
---
--,--
--